Engine, Transmission, wheels/Tyres and Heating/Cooling
- Browse Modified, Uprated & Alternative Parts
- CLICK TO VIEW
MODIFIED PARTS - Browse Original Triumph Catalogue Plates
TR3 Plate C - ENGINE: WATER PUMP ASSEMBLY AND DYNAMO MOUNTING (Not illustrated).
| Plate No. | Part No. | Description and Comments | No Per Unit | Price | Add to Cart | |
|---|---|---|---|---|---|---|
 |
C1AA | 501488 |
WATER PUMP ASSEMBLYRevington TR information: This assembly consists of the water pump housing and the pulley. It is more usual to require the bearing housing and reuse your existing pulley, as it is the bearing housing assembly that gives up. Order... READ MORE |
1 |
£79.36 Ex VAT @ 20% |
|
|
C1 | 057014 |
Body, water pumpRevington TR information: New steel parts are no longer available. We can however supply new aluminium castings, part number 057014AL or good second-hand steel castings. Order part number 057014SH |
1 |
£220.80 Ex VAT @ 20% |
|
|
C2 | 056243 |
Stud, bearing housing attachmentThis item has been superceded by ST706101 - see below |
2 | ||
|
ST706101 |
STUD 3/8 X 1-1/4" 1/2UNF+1/2UNC |
2 |
£4.12 Ex VAT @ 20% |
||
|
C3 | 114774 |
PlugRevington TR information: The original square headed taper plug 114774 is used as an axle filler, drain plug and as a blank in the cooling system when a heater is not fitted. Revington TR recommend using a magnetic drain... READ MORE |
1 |
£5.87 Ex VAT @ 20% |
|
|
C3A | 106969 |
Housing, bearing assemblyRevington TR information: This is what is usually sold as a 'Water Pump'. The assembly consisting of: the pump bearing housing, impeller, spindle, bearings and seals. You might consider rebuilding your original unit, we have all the parts... READ MORE |
1 |
£107.92 Ex VAT @ 20% |
|
|
C4 | 200287 |
Housing, bearingRevington TR information: NLA use 200287SH |
1 | ||
|
C5 | 508721 |
Nipple, grease, In housingTriumph Catalogue Remarks: From Engine No. 1 |
1 | ||
|
C5A | 125361 |
Nipple, grease, In housingTriumph Catalogue Remarks: From Engine No. __________ |
1 |
£2.11 Ex VAT @ 20% |
|
|
C6 | 105504 |
Spindle |
1 | ||
|
C7 | 100858 |
Seal, between bearing housing and impellorThis item has been superceded by 88G446 - see below |
1 | ||
|
88G446 |
SEAL WATER PUMPRevington TR information: Use 148322 |
1 |
£17.64 Ex VAT @ 20% |
||
|
C8 | 105981 |
Impellor |
1 |
£14.06 Ex VAT @ 20% |
|
|
C9 | 060313 |
Seal, bearingRevington TR information: Seal in between bearings and housing TR2-6 water pump. This 'seal' appears to just float between the circlip and the housing in the bearing side of the engines coolant (water) pump. It is rather over stating... READ MORE |
1 | ||
|
C10 | 101092 |
Washer, abutmentThis item has been superceded by WP11014098 - see below |
1 | ||
|
WP11014098 |
WASHER PLAIN 5/8 X 7/8 X .098 INCH |
1 |
£2.82 Ex VAT @ 20% |
||
|
C11 | 500047 |
Circlip, between seal and washerRevington TR information: Our stock are genuine Leyland parts |
1 |
£0.40 Ex VAT @ 20% |
|
|
C12 | 100978 |
BearingRevington TR information: This water pump bearing is of a special design with one sealed face and seems to have been a special design especially for water pumps of the TR2-4A era. This means that when available it is... READ MORE |
2 |
£101.75 Ex VAT @ 20% |
|
|
C13 | 100760 |
Piece, distance, between bearingsThis item has been superceded by PB12820165 - see below |
1 | ||
|
PB12820165 |
SLEEVE STEEL 7/8" x 5/8" x 1" longRevington TR information: Steel sleeve 7/8" o/d, 5/8" i/d and 1" long (actual dimensions 0.884" x 0.369 x 0.998"). Our stock of these sleeves is new old stock Standard Triumph and is the spacer between the bearings... READ MORE |
1 |
£1.49 Ex VAT @ 20% |
||
|
C14 | 100763 |
Circlip, retaining bearing in housing |
1 |
£1.34 Ex VAT @ 20% |
|
|
C15 | 105537 |
Pulley, water pumpRevington TR information: Steel standard pulley water pump pulley. We have second hand original parts in stock to if originality is important. Order aluminium pulley RTR5122 if you have a thin belt conversion. For this and the pulley location... READ MORE |
1 |
£49.42 Ex VAT @ 20% |
|
|
C16 | KW0420 |
Key, locating pulley on spindle |
1 | ||
|
C17 | TN3208 |
Nut, nyloc, pulley on spindle |
1 | ||
|
C18 | 100766 |
Washer, under nutThis item has been superceded by WP10514162 - see below |
1 | ||
|
WP10514162 |
WASHER PLAIN 5/16" x 7/8" x 0.162" |
1 |
£1.22 Ex VAT @ 20% |
||
|
C19 | 056214 |
Washer, joint, bearing housing to pump bodyThis item has been superceded by 138587 - see below |
1 | ||
|
138587 |
GASKET WATER PUMP TR2-4A |
1 |
£2.56 Ex VAT @ 20% |
||
|
C20 | HN2009 |
Nut, securing bearing housing |
2 | ||
|
C21 | WL0209 |
Washer, spring, under nutThis item has been superceded by GHF333 - see below |
2 | ||
|
GHF333 |
[GHF333] |
2 |
£0.43 Ex VAT @ 20% |
||
|
C22 | 056237 |
Washer, joint, water pump to blockThis item has been superceded by 138586 - see below |
1 | ||
|
138586 |
W/PUMP GASKET |
1 |
£3.06 Ex VAT @ 20% |
||
|
C23 | HB0971 |
Bolt, bearing housing and pump body to block |
1 | ||
|
C24 | HB0968 |
Bolt, pump body to block |
2 | ||
|
C25 | WL0209 |
Washer, spring, under nutThis item has been superceded by GHF333 - see below |
3 | ||
|
GHF333 |
[GHF333] |
3 |
£0.43 Ex VAT @ 20% |
||
|
C26 | 058924 |
Belt, fanThis item has been superceded by GFB40975 - see below |
1 | ||
|
GFB40975 |
FAN BELT TR2-4ARevington TR information: This is the standard "fat belt". 20mm x 975mm For the thin belt see GCB10975 |
1 |
£25.33 Ex VAT @ 20% |
||
|
C26A | 102266 |
Pulley, dynamoRevington TR information: Dynamo steel pulley to original dimensions. Consider also original second hand part 102266SH. If you are considering running a thin belt conversion to drive your dynamo you will need aluminium thin belt pulley 12G2102A. ... READ MORE |
1 |
£40.02 Ex VAT @ 20% |
|
|
C26B | 102986 |
Fan, assemblyRevington TR information: Not available new. Use second hand part 102986SH. |
1 | ||
|
C26C | 058912 |
Bracket, dynamo supportRevington TR information: Consider second-hand part 058912SH Revington TR have three alternator/dynamo brackets available. 058912 Original TR2-4A dynamo mount. This bracket has its legs 102mm apart measured externally and 94mm internally (the material is 4mm thick). This bracket suits... READ MORE |
1 |
£22.63 Ex VAT @ 20% |
|
|
C26D | HU0856 |
Screw, set, bracket to cylinder block |
3 | ||
|
C26E | WL0208 |
Washer, spring, on setscrewThis item has been superceded by WS105090853 - see below |
3 | ||
|
WS105090853 |
WASHER SPRING 5/16" ID RECT SECTION |
3 |
£0.25 Ex VAT @ 20% |
||
|
C26F | 059015 |
Pedestal, dynamoRevington TR information: TR2-4A Dynamo mounting pedestal. This part has an effective length of 1.5" For dynamo mounting detail see plate M in the TR4A original parts book or Plate M on our web site. |
1 |
£24.84 Ex VAT @ 20% |
|
|
C26G | TN3211 |
Nut, nyloc, pedestal attachment |
1 | ||
|
C26H | HU0808 |
Screw, set, dynamo bracketTriumph Catalogue Remarks: From Engine No. 1 |
1 | ||
|
C26J | TN3208 |
Nut, locking screwTriumph Catalogue Remarks: From Engine No. 1 |
1 | ||
|
C26K | 113094 |
Bolt, dynamo to bracketTriumph Catalogue Remarks: From Engine No. 10346E |
1 | ||
|
BH605101 |
BOLT 5/16 UNF X 1-1/4 INCHRevington TR information: For dynamo mounting detail see plate M in the TR4A original parts book or web site. |
1 |
£1.37 Ex VAT @ 20% |
||
|
C26L | WP0008 |
Washer, plain, dynamo to bracketTriumph Catalogue Remarks: From Engine No. 10346E |
A/R | ||
|
WP10510075 |
WASHER PLAIN 5/16" x 5/8" x 0.075" |
A/R |
£0.44 Ex VAT @ 20% |
||
|
C26M | WP0133 |
Washer, plain, dynamo to bracketTriumph Catalogue Remarks: From Engine No. 10346E |
A/R | ||
|
PWZ305 |
WASHER |
A/R |
£1.27 Ex VAT @ 20% |
||
|
C26N | 059115 |
Bolt, dynamo to pedestalThis item has been superceded by BH605111 - see below |
1 | ||
|
BH605111 |
BOLT 5/16 UNF X 1-3/8 INCHRevington TR information: For dynamo mounting detail see plate M in the TR4A original parts book or web site. |
1 |
£1.08 Ex VAT @ 20% |
||
|
C26O | WL0208 |
Washer, spring, on boltThis item has been superceded by WS105090853 - see below |
1 | ||
|
WS105090853 |
WASHER SPRING 5/16" ID RECT SECTION |
1 |
£0.25 Ex VAT @ 20% |
||
|
C26P | 058914 |
Link, adjusting dynamoRevington TR information: Consider second hand original part 058914SH or powder coated black part |
1 |
£17.26 Ex VAT @ 20% |
|
|
C26Q | HU0857 |
Screw, set, link to water pump body |
1 | ||
|
C26R | HB0859 |
Bolt, link to water pump body |
1 | ||
|
C26S | 106706 |
Washer, tab, on setscrew |
1 |
£9.55 Ex VAT @ 20% |
|
|
C26T | HU0857 |
Screw, set, link to dynamoTriumph Catalogue Remarks: From Engine No. 1 |
1 | ||
|
C26U | WP0008 |
Washer, plain, on setscrewTriumph Catalogue Remarks: From Engine No. 1 |
1 | ||
|
WP10510075 |
WASHER PLAIN 5/16" x 5/8" x 0.075" |
1 |
£0.44 Ex VAT @ 20% |
||
|
C26V | WP0017 |
Washer, plain, each side of linkTriumph Catalogue Remarks: From Engine No. 1 |
2 | ||
|
WP10516057 |
WASHER 5/16 X 1 INCH ODX16 SWG |
2 |
£0.43 Ex VAT @ 20% |
||
|
C26W | HB0859 |
Bolt, link to dynamoTriumph Catalogue Remarks: From Engine No. 10346 |
1 | ||
|
C26W | WP-00119 |
Washer, plain, under bolt headTriumph Catalogue Remarks: From Engine No. 10346 |
1 | ||
|
C26X | WP0017 |
Washer, plain, between link and dynamo flangeTriumph Catalogue Remarks: From Engine No. 10346 |
1 | ||
|
WP10516057 |
WASHER 5/16 X 1 INCH ODX16 SWG |
1 |
£0.43 Ex VAT @ 20% |
||
|
C26Y | JN2158 |
Nut, securing link to dynamoTriumph Catalogue Remarks: From Engine No. 10346 |
1 |
£0.65 Ex VAT @ 20% |
